LightRail 4.20 Nuts and Bolts Archives - LightRail® Light Movers

Q: LightRail Rail Alignment Pins

LightRail Rail Alignment Pins allow the LightRail Motor to cross the seam from one Light Rail System Rail to another. Typically we would not want that because each grow light would stay on its own grow equipment Rail area. And, that keeps the plants from waiting too long for the grow light to come back. Exceptions which would allow for longer grow light travel distances would be the indoor greenhouse or off season greenhouse that has some natural indoor plant light available. And, low light plants such as seedlings or lettuce could use a longer grow light system run. LightRail Rail Alignment Pins are compatible with LightRail 3.0, LightRail 3.5, LightRail 4.0 and LightRail 4.20 exclusively.

Q: Light Rail Fastener for Strut Channel Compatible Rail

LightRail Fastener for Strut Channel Compatible Rail: This is the LightRail fastener for strut channel. And, it's a custom fastening light mover rail system. It is specifically made for mounting LightRail strut channel compatible Rails to commercial strut channel. And, this indoor grow system can be either inline, perpendicular, at a 45 degree, or at any angle. In other words, it works for any configuration . LightRail fastener for strut channel compatible rails come two per custom rail See how this works: Custom Unistrut Compatible Rails Available for Indoor Grow Setups . Note: This fastener is compatible with LightRail strut channel compatible Rails only. And, two of these fasteners come with each LightRail strut channel compatible light mover rail. They work with LightRail 3.0, LightRail 3.5, LightRail 4.0 and LightRail 4.20. But, they do not work with LightRail 5.0. Hint: For heavier indoor grow lights, it is recommended to use one or two extra fasteners per light mover rail. And, that's to achieve extra support for the full Rail length. How do LightRail light movers work? It’s a two-part effect and can move all grow light systems: Grow Lamp Bravery – Yield as a Verb for the Indoor Grow Room Setup The benefits of automation for our grow light systems

Q: Light Rail Switch Stops – Slide Nuts & Thumb Screws

SS KIT 2 LightRail Switch Stop details LightRail Switch Stop Stoppers – Slide Nuts and Thumb Screws: Compatible with LightRail 3.0, 3.5, 4.0 and 4.20. The Switch Stop stoppers are used to stop the LightRail Motor at the desired location along the light mover rail. And, this is also the location that the Motor would then switch directions. Also, the Switch Stop stoppers can be set anywhere along the light mover rail for a wide range of grow light travel distance settings. For more information about this grow equipment setting and how that works, here is a good link on the grow room setup stopper placement on the light mover rail. The Switch Stop stoppers come two sets to a package, one for each end of the light mover rail. So, that equals a total of two slide nuts and two thumb screws. How do LightRail grow light movers work? How does a LightRail grow light setup work? LightRail turns the lights of your indoor growing system into the best grow lights they can be. See how this works: Grow Lamp Bravery – Yield as a Verb for Indoor Growing Systems. And, see the benefits of automation for our grow light systems .

Q: Light Rail Drive Unit Hardware Pack

DU HP LightRail Drive Unit Hardware Pack LightRail Drive Unit Hardware Pack: The Drive Unit Hardware Pack is the installation hardware that comes with LightRail 3.5, 4.0 and 4.20. And, it includes an eye screw and 12 light mover rail mounting screws. It also includes 2 switch stop stoppers as slide nuts and thumb screws and a cable tie.

Rated 5.00 out of 5

~~$15.00~~ $12.00

Add to cart Details